An Easy Plumbing Guide for Bathtub Installation
An Easy Plumbing Guide for Bathtub Installation
Blog Article
Each person may have their personal opinion with regards to Tools You Need to Install a New Bathtub .
Installing a bathtub isn't exactly brain surgery, but it does require strong plumbing, woodworking, and also in some cases, tiling skills. Replacing an old bath tub with a brand-new one is additionally a moderately hard task. If the old tub is readily available, the project can move quickly; if you need to open a wall to remove the old bathtub and also position the brand-new tub, the task is a lot harder. In either situation, the task is within a residence handyman's abilities, although you will certainly need a helper to vacate the old tub as well as set in the brand-new one. Make sure you have qualified yourself for the task and also are comfortable trying it. As opposed to hiring a specialist to take control of a halfway-completed project, it is much better to take into consideration using one prior to you begin. Opportunities are you might require an expert plumber to make tube connections.
This short article will help you mount a brand-new tub in your shower room if you have already gotten a new tub and also do not need to change the setup of your previous water system pipes.
Your devices and material list should comprise the following:
Preparing for the Installation
Firstly, the supporting frame provided with the bathroom should be fitted (if called for) according to the supplier's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is necessary to make certain that if the faucet includes a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the taps unit to stop stress on the bath tub.
Fit the versatile tap adapters to the bottom of the two faucets using 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Make certain you use all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom ought to currently prepare to be suited its last setting.
Removing Old Touches
If you require to change old faucets with new ones as a part of your installment, after that the first thing you need to do is disconnect the supply of water. After doing so, switch on the taps to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be rather problematic due to the limited accessibility that is usually the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipes to the faucets. Have a cloth ready for the continuing to be water that will certainly come from the pipes. As soon as the supply pipes have been gotten rid of, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming during this process. Once the faucets have been removed, the holes in the bath/basin will need to be cleansed of any kind of old sealing substance.
Prior to proceeding to fit the brand-new taps, compare the pipe links on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.
Mounting the Bath tub
Making use of the two wooden boards under its feet, put the tub in the required position. The wooden boards are valuable in equally spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 tiny factors.
The following goal is to make sure that the bath tub is leveled all round. This can be attained by examining the spirit level and also readjusting the feet on the tub until the spirit level reviews level.
To install faucets, fit all-time low of the furthest adaptable tap port to the suitable supply pipeline by making a compression join; after that do the same for the other faucet.
Activate the water supply and also examine all joints as well as brand-new pipework for leaks and tighten them if needed. Fill the bath tub and likewise inspect the overflow outlet as well as the regular outlet for leaks.
Ultimately, take care of the bath paneling as defined in the maker's user's manual. Tiling and also securing around the bath tub should wait until the bathtub has actually been used a minimum of when as this will certainly resolve it right into its last placement.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will certainly require a plastic connector to stop damages to the string. One end of the port fits on the plastic tail of the tap as well as the other end provides a link to the current supply pipes.
If you require to fit a monobloc, after that you will need decreasing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, place the tap in the placing hole in the bath/basin guaranteeing that the washing machines remain in location between the faucet and also the sink. Protect the tap in place with the maker supplied backnut. As soon as the tap is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with typical faucet ports. The previous type needs to be connected to the tap finishes first, tightening up only by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the location where the bathroom meets the tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to break a rigid seal, triggering the water to permeate the wall surface in between the bathroom and also the tiling, leading to complications with moisture and possible leaks to the ceiling below.
You can choose from a range of coloured sealants to blend in your components as well as fittings. They are offered in tubes as well as cartridges, and can sealing gaps up to a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of soaked paper or soft rope. Bear in mind to always load the tub with water before sealing, to permit the motion experienced when the bathtub is in usage. The sealant can crack rather early if you do not take into consideration this movement prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also easily offered on the marketplace. It is recommended to fit the ceramic tiles making use of waterproof or waterproof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
I hope you enjoyed our part on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks for finding the time to browse our article post. Appreciated our entry? Please share it. Let someone else discover it. Thanks for your time invested reading it.
Secure timely emergency plumbing assistance. Report this page